DB Drive Speed Series Amplifier SPA SPA150.4 Manual de instrucciones Pagina 131
- Pagina / 168
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
Appendix 6. Compliance to EU EC Directives
A6 - 2
Appendix 6-1 Compliance to EC Directives
Appendix 6-1-1 European EC Directives
In the EU Community, the attachment of a CE mark (CE marking) is mandatory to indicate that the basic
safety conditions of the Machine Directives (issued Jan. 1995), EMC Directives (issued Jan. 1996) and
the Low-voltage Directives (issued Jan. 1997) are satisfied. The machines and devices in which the
servo and spindle drive are assembled are the targets for CE marking.
(1) Compliance to EMC Directives
The servo and spindle drive are components designed to be used in combination with a machine or
device. These are not directly targeted by the Directives, but a CE mark must be attached to
machines and devices in which these components are assembled. The next section "EMC
Installation Guidelines", which explains the unit installation and control panel manufacturing
method, etc., has been prepared to make compliance to the EMC Directives easier.
(2) Compliance to Low-voltage Directives
The MDS-C1-SPA Series units are targeted for the Low-voltage Directives. An excerpt of the
precautions given in this specification is given below. Please read this section thoroughly before
starting use.
A Self-Declaration Document has been prepared for the EMC Directives and Low-voltage
Directives. Contact Mitsubishi or your dealer when required.
Appendix 6-1-2 Cautions for EC Directive compliance
Use the Low-voltage Directive compatible parts for the servo/spindle drive and servo/spindle motor. In
addition to the items described in this instruction manual, observe the items described below.
(1) Configuration
Use a type B (AC/DC detectable type) breaker
Isolating
transformer
Circuit breaker
AC reactor
Electromagnetic
contactor
Drive unit
CB
MC
M
(2) Environment
Use the units under an Overvoltage Category II and Pollution Class of 2 or less environment as
stipulated in IEC60664.
These units do not provide protection against electric shock and fire sufficient for the requirements
of the Low-voltage Directive and relevant European standards by themselves, so provide additional
protection (refer to 5.2.4 and 7.1.6.1 of EN50178)
Drive unit Motor
During
operation
Storage
During
transportation
During
operation
Storage
During
transportation
Ambient
temperature
0°C to 55°C -15°C to 70°C -15°C to 70°C
Ambient
temperature
0°C to 40°C -15°C to 70°C -15°C to 70°C
Humidity
90%RH or
less
90%RH or
less
90%RH or less Humidity
80%RH or
less
90%RH or
less
90%RH or
less
Altitude
1000m or
less
1000m or
less
13000m or
less
Altitude
1000m or
less
1000m or
less
13000m or
less
- Introduction 3
- Notes on Reading This Manual 3
- Precautions for safety 4
- 1. Electric shock prevention 5
- 1. Fire prevention 5
- 2. Injury prevention 5
- 3. Various precautions 6
- CONTENTS 11
- 1. Introduction 14
- 1-1-1 System configuration 15
- 1-1-2 Unit outline type 16
- 1-2 Explanation of type 17
- MDS-C1 18
- MDS-C1 19
- B-AL 20
- 2. Specifications 21
- 2-1 Spindle motor 22
- 2-2 Drive unit 32
- function 33
- 2-2-3 Power supply unit 37
- 2-2-4 AC reactor 38
- 2-3-1 Layout of unit 42
- 3. Characteristics 45
- 3-1 Spindle motor 46
- 3-2-2 Heating value 48
- 4. Dedicated Options 49
- (1020p/rev encoder) 50
- 4-1-1 Magnetic sensor 51
- A phase 54
- Z phase 54
- B phase 54
- Item Model Contents 57
- • monitor 59
- 5. Peripheral Devices 60
- 5-1 Selection of wire 61
- 5-3 Earth leakage breaker 65
- Time constant: T=6 66
- 5-5 Noise filter 67
- 5-6 Surge absorber 68
- Overload (for one minute) 69
- 50%ED (15-minute) 69
- (30-minute) zone 69
- Cooling 73
- Terminal box 74
- Exhaust air 74
- Cooling fan 74
- Cross section 74
- Appendix 1-1-2 SJ-V Series 75
- Appendix 1-1-3 SJ-VS Series 85
- MDS-C1-SPA-55 87
- MDS-C1-SPA-75 87
- MDS-C1-SPA-110 87
- MDS-C1-SPA-150 88
- MDS-C1-SPA-185 88
- For MDS-C1-SP 89
- MDS-C1-SPA-260 90
- MDS-C1-SPA-300 90
- MDS-C1-CV-37 91
- MDS-C1-CV-55 91
- MDS-C1-CV-75 91
- MDS-C1-CV-110 92
- MDS-C1-CV-150 93
- MDS-C1-CV-185 93
- MDS-C1-CV-220 94
- MDS-C1-CV-260 94
- MDS-C1-CV-300 94
- MDS-C1-CV-370 94
- Appendix 1-2-3 AC rector 95
- [Unit: mm] 96
- CAUTION 101
- Appendix 3. Selection 106
- MDS-C1-SPA-220 108
- No.1 MDS-C1-SPA-55 108
- Unit Specifications 109
- Appendix 4-1-1 Outline 110
- [Unit : mm] 111
- – – M8 M10 118
- M10 M6 M10 M6 M10 M10 118
- M4 M4 M4 M4 118
- M4 M4 – – 118
- M8 M10 – – 118
- MDS-B-SPA(H) 119
- -040 to 37 119
- MDS-C1-SPA(H) 119
- -55 to 300 119
- MDS-B-SPA-450 MDS-B-CVE-450 120
- Appendix 4-1-12 Parameters 122
- Appendix 4-1-13 Precautions 122
- Drive Unit Specifications 123
- Appendix 5-1-1 Outline 124
- Panel mounting hole 125
- Less than 55dB 126
- Motor 131
- PE terminal 132
- Spindle 133
- Appendix 7-1 Introduction 135
- Appendix 7-3 EMC measures 136
- Breaker 137
- Noise Noise 138
- Control panel 138
- To earthing 139
- Spindle side connector 140
- Appendix 7-6-2 Ferrite core 142
- 40A item 144
- (250V series) (500V series) 144
- (Installation hole) 147
- (1)Black (2)Black (3)Black 148
- UL/c-UL Standard 150
- 1. UL/c-UL listed products 151
- 3. Notes for CNC system 152
- 4.4 Peripheral devices 153
- 4.5 Flange of servo motor 153
- 5-1 Use S Analog Drive Unit 159
- Certification 161
- Revision History 165
- Duplication Prohibited 167
Relacionado con productos y manuales para Amplificadores de audio DB Drive Speed Series Amplifier SPA SPA150.4
(28 paginas)© 2020, manymanuals.es. Todos los derechos reservados | 0.046 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales