DB Drive Speed Series Amplifier SPA SPA150.4 Manual de instrucciones Pagina 53
- Pagina / 168
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
4. Dedicated Options
4 - 5
(3) Caution on installation of magnet
Observe the following cautions when installing the magnet to the spindle.
(a) Do not place an intense magnetic source near the magnet.
(b) Carefully handle the magnet, avoiding mechanical shock to the magnet.
(c) Secure the magnet to the spindle with M4 screws.
(d) After the magnet is installed, balance the entire spindle.
(e) Align the center of the magnet with the center line of the rotating disk on the spindle. (For the
position relation, refer to the maintenance instruction manual.)
(f) Keep the magnet and its peripheral clean avoiding iron particles and cutting chips from adhering
to the magnet. Failure to observe this could result in malfunction.
(g) Apply lock paint, or other suitable means, to prevent installation screws from becoming loose.
(h) If the magnet is installed on a ground rotating disk, demagnetize the disk because the rotating
disk is thought to be magnetized.
(i) Diameter of rotating disk on which the magnet is installed should be within the range from 80mm
to 120mm. If this range is exceeded, the magnet may be damaged and the orient control may
not be carried out correctly although the speed is below the tolerable speed of the magnet.
(j) If rotation speed of the spindle on which the magnet is installed exceeds 6,000r/min, use a
high-speed type magnet (applicable up to 12,000r/min of rotation speed). If rotation speed
exceeds 12,000r/min, use a ring type magnet.
(k) When installing the magnet on a rotating body plane, keep the speed below 6,000r/min.
(4) Caution on installation of sensor
Observe the following cautions when installing the sensor.
(a) The center line of head should be in line with the center of magnet.
(b) Connector used in preamplifier
BKO-C1810 : Oil proof-type
BKO-C1730 : Not oil proof-type
Install both type at a place not subject to oil.
(c) The cable between the preamplifier and the controller should be laid down apart from
high-voltage cables.
(d) Check the connector wiring, securely engage the receptacle and tighten connector lock screws.
- Introduction 3
- Notes on Reading This Manual 3
- Precautions for safety 4
- 1. Electric shock prevention 5
- 1. Fire prevention 5
- 2. Injury prevention 5
- 3. Various precautions 6
- CONTENTS 11
- 1. Introduction 14
- 1-1-1 System configuration 15
- 1-1-2 Unit outline type 16
- 1-2 Explanation of type 17
- MDS-C1 18
- MDS-C1 19
- B-AL 20
- 2. Specifications 21
- 2-1 Spindle motor 22
- 2-2 Drive unit 32
- function 33
- 2-2-3 Power supply unit 37
- 2-2-4 AC reactor 38
- 2-3-1 Layout of unit 42
- 3. Characteristics 45
- 3-1 Spindle motor 46
- 3-2-2 Heating value 48
- 4. Dedicated Options 49
- (1020p/rev encoder) 50
- 4-1-1 Magnetic sensor 51
- A phase 54
- Z phase 54
- B phase 54
- Item Model Contents 57
- • monitor 59
- 5. Peripheral Devices 60
- 5-1 Selection of wire 61
- 5-3 Earth leakage breaker 65
- Time constant: T=6 66
- 5-5 Noise filter 67
- 5-6 Surge absorber 68
- Overload (for one minute) 69
- 50%ED (15-minute) 69
- (30-minute) zone 69
- Cooling 73
- Terminal box 74
- Exhaust air 74
- Cooling fan 74
- Cross section 74
- Appendix 1-1-2 SJ-V Series 75
- Appendix 1-1-3 SJ-VS Series 85
- MDS-C1-SPA-55 87
- MDS-C1-SPA-75 87
- MDS-C1-SPA-110 87
- MDS-C1-SPA-150 88
- MDS-C1-SPA-185 88
- For MDS-C1-SP 89
- MDS-C1-SPA-260 90
- MDS-C1-SPA-300 90
- MDS-C1-CV-37 91
- MDS-C1-CV-55 91
- MDS-C1-CV-75 91
- MDS-C1-CV-110 92
- MDS-C1-CV-150 93
- MDS-C1-CV-185 93
- MDS-C1-CV-220 94
- MDS-C1-CV-260 94
- MDS-C1-CV-300 94
- MDS-C1-CV-370 94
- Appendix 1-2-3 AC rector 95
- [Unit: mm] 96
- CAUTION 101
- Appendix 3. Selection 106
- MDS-C1-SPA-220 108
- No.1 MDS-C1-SPA-55 108
- Unit Specifications 109
- Appendix 4-1-1 Outline 110
- [Unit : mm] 111
- – – M8 M10 118
- M10 M6 M10 M6 M10 M10 118
- M4 M4 M4 M4 118
- M4 M4 – – 118
- M8 M10 – – 118
- MDS-B-SPA(H) 119
- -040 to 37 119
- MDS-C1-SPA(H) 119
- -55 to 300 119
- MDS-B-SPA-450 MDS-B-CVE-450 120
- Appendix 4-1-12 Parameters 122
- Appendix 4-1-13 Precautions 122
- Drive Unit Specifications 123
- Appendix 5-1-1 Outline 124
- Panel mounting hole 125
- Less than 55dB 126
- Motor 131
- PE terminal 132
- Spindle 133
- Appendix 7-1 Introduction 135
- Appendix 7-3 EMC measures 136
- Breaker 137
- Noise Noise 138
- Control panel 138
- To earthing 139
- Spindle side connector 140
- Appendix 7-6-2 Ferrite core 142
- 40A item 144
- (250V series) (500V series) 144
- (Installation hole) 147
- (1)Black (2)Black (3)Black 148
- UL/c-UL Standard 150
- 1. UL/c-UL listed products 151
- 3. Notes for CNC system 152
- 4.4 Peripheral devices 153
- 4.5 Flange of servo motor 153
- 5-1 Use S Analog Drive Unit 159
- Certification 161
- Revision History 165
- Duplication Prohibited 167
Relacionado con productos y manuales para Amplificadores de audio DB Drive Speed Series Amplifier SPA SPA150.4
(28 paginas)© 2020, manymanuals.es. Todos los derechos reservados | 0.097 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales