DB Drive Speed Series Amplifier SPA SPA150.4 Manual de instrucciones Pagina 137
- Pagina / 168
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
Appendix 7. EMC Installation Guidelines
A7 - 4
Appendix 7-4-2 Measures for door
(1) Use metal for all materials configuring the door.
(2) Use an EMI gasket or conductive packing for the contact between the door and control panel unit.
(3) The EMI gasket or conductive packing must contact at a uniform and correct position of the metal
surface of the control panel unit.
(4) The surface of the control panel unit contacted with the EMI gasket or conductive packing must
have conductance treatment.
Example) Weld (or screw) a plate that is plated (with nickel, tin).
EMI gasket
Packing
Carry out conductance treatment on
sections that the EMI gasket contacts.
Door
Control panel
(5) As a method other than the above, the control panel unit and door can be connected with a plain
braided wire. In this case, the panel and door should be contacted at as many points as possible.
Appendix 7-4-3 Measures for operation board panel
(1) Always connect the operation board and indicator with an earthing wire.
(2) If the operation board panel has a door, use an EMI gasket or conductive packing between the door
and panel to provide electrical conductance in the same manner as the control panel.
(3) Connect the operation board panel and control panel with a sufficiently thick and short earthing
wire.
Refer to the "EMC INSTALLATION GUIDELINES" BNP-B2230 for the NC for more details.
Appendix 7-4-4 Shielding of the power supply input section
(1) Separate the input power supply section from other parts in the control panel so that the input
power supply cable will not be contaminated by radiated noise.
(2) Do not lead the power line through the panel without passing it through a filter.
The power supply line noise is eliminated
by the filter, but cable contains noise again
because of the noise radiated in the control
panel.
Use a metal plate, etc., for the shielding
partition. Make sure not to create a
clearance.
Drive unit
Power
line filter
Breaker
Control panel
A
C input
Radiated
noise
Drive unit
Power
line filter
Breaker
Control panel
A
C input
Radiated
noise
Shielding
plate
- Introduction 3
- Notes on Reading This Manual 3
- Precautions for safety 4
- 1. Electric shock prevention 5
- 1. Fire prevention 5
- 2. Injury prevention 5
- 3. Various precautions 6
- CONTENTS 11
- 1. Introduction 14
- 1-1-1 System configuration 15
- 1-1-2 Unit outline type 16
- 1-2 Explanation of type 17
- MDS-C1 18
- MDS-C1 19
- B-AL 20
- 2. Specifications 21
- 2-1 Spindle motor 22
- 2-2 Drive unit 32
- function 33
- 2-2-3 Power supply unit 37
- 2-2-4 AC reactor 38
- 2-3-1 Layout of unit 42
- 3. Characteristics 45
- 3-1 Spindle motor 46
- 3-2-2 Heating value 48
- 4. Dedicated Options 49
- (1020p/rev encoder) 50
- 4-1-1 Magnetic sensor 51
- A phase 54
- Z phase 54
- B phase 54
- Item Model Contents 57
- • monitor 59
- 5. Peripheral Devices 60
- 5-1 Selection of wire 61
- 5-3 Earth leakage breaker 65
- Time constant: T=6 66
- 5-5 Noise filter 67
- 5-6 Surge absorber 68
- Overload (for one minute) 69
- 50%ED (15-minute) 69
- (30-minute) zone 69
- Cooling 73
- Terminal box 74
- Exhaust air 74
- Cooling fan 74
- Cross section 74
- Appendix 1-1-2 SJ-V Series 75
- Appendix 1-1-3 SJ-VS Series 85
- MDS-C1-SPA-55 87
- MDS-C1-SPA-75 87
- MDS-C1-SPA-110 87
- MDS-C1-SPA-150 88
- MDS-C1-SPA-185 88
- For MDS-C1-SP 89
- MDS-C1-SPA-260 90
- MDS-C1-SPA-300 90
- MDS-C1-CV-37 91
- MDS-C1-CV-55 91
- MDS-C1-CV-75 91
- MDS-C1-CV-110 92
- MDS-C1-CV-150 93
- MDS-C1-CV-185 93
- MDS-C1-CV-220 94
- MDS-C1-CV-260 94
- MDS-C1-CV-300 94
- MDS-C1-CV-370 94
- Appendix 1-2-3 AC rector 95
- [Unit: mm] 96
- CAUTION 101
- Appendix 3. Selection 106
- MDS-C1-SPA-220 108
- No.1 MDS-C1-SPA-55 108
- Unit Specifications 109
- Appendix 4-1-1 Outline 110
- [Unit : mm] 111
- – – M8 M10 118
- M10 M6 M10 M6 M10 M10 118
- M4 M4 M4 M4 118
- M4 M4 – – 118
- M8 M10 – – 118
- MDS-B-SPA(H) 119
- -040 to 37 119
- MDS-C1-SPA(H) 119
- -55 to 300 119
- MDS-B-SPA-450 MDS-B-CVE-450 120
- Appendix 4-1-12 Parameters 122
- Appendix 4-1-13 Precautions 122
- Drive Unit Specifications 123
- Appendix 5-1-1 Outline 124
- Panel mounting hole 125
- Less than 55dB 126
- Motor 131
- PE terminal 132
- Spindle 133
- Appendix 7-1 Introduction 135
- Appendix 7-3 EMC measures 136
- Breaker 137
- Noise Noise 138
- Control panel 138
- To earthing 139
- Spindle side connector 140
- Appendix 7-6-2 Ferrite core 142
- 40A item 144
- (250V series) (500V series) 144
- (Installation hole) 147
- (1)Black (2)Black (3)Black 148
- UL/c-UL Standard 150
- 1. UL/c-UL listed products 151
- 3. Notes for CNC system 152
- 4.4 Peripheral devices 153
- 4.5 Flange of servo motor 153
- 5-1 Use S Analog Drive Unit 159
- Certification 161
- Revision History 165
- Duplication Prohibited 167
Relacionado con productos y manuales para Amplificadores de audio DB Drive Speed Series Amplifier SPA SPA150.4
(28 paginas)ShoreLand'r SLRB34BXLW V.2 Handbücher
Bedienungsanleitungen und Benutzerhandbücher für Anhänger ShoreLand'r SLRB34BXLW V.2.
Wir stellen 1 PDF-Handbücher ShoreLand'r SLRB34BXLW V.2 zum kostenlosen herunterladen nach Dokumenttypen zur Verfügung Bedienungsanleitung
Comentarios a estos manuales